Added arduino libs

libraries/EnableInterrupt/examples/HiSpeed/HiSpeed.ino

@@ -0,0 +1,64 @@
+// EnableInterrupt HiSpeed example sketch
+// See https://github.com/GreyGnome/EnableInterrupt and the README.md for more information.
+
+// This example demonstrates the use of the EnableInterrupt library on a single pin of your choice.
+// It uses the "HiSpeed" mode of the library.
+// This has only been tested on an Arduino Duemilanove and Mega ADK.
+// It is designed to work with the Arduino Duemilanove/Uno, Arduino Mega2560/ADK, the Arduino
+// Leonardo, and the Arduino Due. Please let me know how you fare on the Leonardo or Due.
+
+// To use:
+
+// 1. You must be using a fairly recent version of the Arduino IDE software on your PC/Mac,
+// that is, version 1.0.1 or later. Check Help->About Arduino in the IDE.
+
+// 2. Wire a simple switch to an Analog or Digital pin (pin 8 in the example below)
+// that supports interrupts. See https://github.com/GreyGnome/EnableInterrupt/wiki/Usage#Summary
+// Attach the other end to a GND pin. A "single pole single throw momentary contact normally
+// open" // pushbutton switch is best for the most interrupting fun.
+// See https://www.sparkfun.com/products/97 and https://octopart.com/b3f-1000-omron-3117
+
+// 3. When pressed, the switch will connect the pin to ground ("low", or "0") voltage, and interrupt the
+// processor. See http://arduino.cc/en/Tutorial/DigitalPins
+
+// 4. The interrupt is serviced immediately, and the ISR (Interrupt SubRoutine) sets the value of a global
+// variable. Open Tools->Serial Monitor in the IDE to see the results of your interrupts.
+
+// 5. Peruse the Examples directory for more elaborate examples.
+
+// 6. Create your own sketch using the EnableInterrupt library!
+
+// Refer to
+// https://github.com/GreyGnome/EnableInterrupt/wiki/Usage#Summary
+
+#define NEEDFORSPEED
+
+#define INTERRUPT_FLAG_PIN8 myvariable_pin8 // NOTICE: NO semicolon!!!
+
+#include <EnableInterrupt.h>
+
+// Attach the interrupt in setup()
+void setup() {
+  //uint8_t pind, pink;
+  Serial.begin(115200);
+  EI_printPSTR("---------------------------------------\r\n");
+  pinMode(8, INPUT_PULLUP);  // Configure the pin as an input, and turn on the pullup resistor.
+                                      // See http://arduino.cc/en/Tutorial/DigitalPins
+  enableInterruptFast(8, CHANGE);
+}
+
+// In the loop, we just check to see where the interrupt count is at. The value gets updated by the
+// interrupt routine.
+void loop() {
+  EI_printPSTR("---------------------------------------\r\n");
+  delay(1000);                          // Every second,
+  if (myvariable_pin8) {
+    EI_printPSTR("Pin 8 was interrupted: ");
+    Serial.print(myvariable_pin8, DEC);      // print the interrupt count.
+    EI_printPSTR(" times so far.\r\n");
+    myvariable_pin8=0;
+  }
+  else {
+    EI_printPSTR("No interrupts.\r\n");
+  }
+}

libraries/EnableInterrupt/examples/HiSpeed/Makefile

@@ -0,0 +1,14 @@
+# Arduino Makefile, see https://github.com/sudar/Arduino-Makefile (it's awesome!)
+BOARD_TAG    = pro
+BOARD_SUB    = 16MHzatmega328
+ARDUINO_PORT = /dev/ttyUSB0
+#BOARD_TAG    = 2560
+#ARDUINO_PORT = /dev/ttyACM0
+ARDUINO_LIBS =
+AVR_TOOLS_DIR = /usr
+
+CFLAGS_STD = -g
+CXXFLAGS_STD = -g
+
+include /usr/share/arduino/Arduino.mk
+

libraries/EnableInterrupt/examples/HiSpeed/README

@@ -0,0 +1,4 @@
+Note: This code has not been tested! Caveat Programmer. I will do it asap.
+(I have tested the HiSpeed code using the HiSpeedTest sketch, so I'm confident
+the library is working properly. Also this sketch compiles.).
+-GreyGnome